OuterSpace / LEGI USA - Steel Fence, Gates, Ornamental Trellis for Commercial and Public Space
LEGI-FLOR Base Anchors: Shall be 80 mm square tube steel with 40 mm wide steel straps welded to sides. Height of anchor to be per manufactureer's recommendations. Hardware: All bolts and nuts shall be hot-dip galvanized or stainless steel. FIT-Fence: hexagonal or removal-resistant 12 mm bolts. R-Fence: hexagonal or removal-resistant bolts, type 2VA, 8X45 mm. See #2.
Fab Pipe Inc. - Products
...- Model RFC Flange Converters - Model DFC Flanged and Machanical Joint Fittings Griffin Pipe Products - Ductile and Cast Iron Fittings Metalfit Flanged Joint Materials Heavy Hex Bolts and Nuts - Model FBZ - Zinc Plated Stud Bolts and Nuts - Model FSB - Model MSB Seal-Tite Flange Gaskets - Model STF - Model STR Flanged Pipe Assembly with Seal-Tite... See #3.
Design Options
...of wind or seismic loading, there is a one-third increase included in the allowable unit stress of the member being designed. 2.4 Primary structural connections use ASTM A-325N bolts and nuts, (5/8 inch diameter and greater) tightened in accordance with the "Turn-of-the-Nut" method. Connections for secondary purlins and girts are made using... See #4.
Walker Display: New Products – Cable Hooks and Ceiling Mounting Kits
...now offer a secure solution for presenting art in front of mirrors, glass or special wall surfaces. The Ceiling Mounting Kit, which consists of 6 ceiling mounting brackets with bolts and nuts and 6 HD mounting snaps, facilitates the mounting of aluminum molding to the ceiling rather than a wall. 552 Ceiling Mounting Kit $9.95 Picture System... See #5.
cst
...steps for poured concrete stairs; for concrete filled steel pan stairs, nosings shall be full length of steps less 1/8" clearance. Nosings shall be furnished with wing anchors, bolts and nuts or concealed cast anchors. All metals shall be furnished in natural metal finish. Feracast shall have one coat of shop applied black paint. HOME CAST... See #6.
Acudor | Floor Hatches - Channel Frame - Aluminum Floor Access Doors
...fabricated from aluminum extrusion with 1-1/2" drainage coupling and integral 1" anchor flange. Hinge: Stainless Steel butt hinges with tamperproof stainless steel bolts and nuts. Opening Device: Automatic hold open arm with red vinyl grip allows door panel to open to 90 degrees, locking door in open position, and allowing for... See #7.
RUBBER FACED PHENOLIC FLANGE ISOLATION KITS
Refinish flange faces if corrective measures do not meet the foregoing. Check flange and bolt hole spot facings for burrs, etc… and clear from facings. Check bolts and nuts and clean. Apply non-conductive lubricant to all threads and flange side of nuts. Align flanges so they are concentric and parallel and install gasket carefully. See #8.
Glossary of Hardware Abbreviations
Standard STMS Strike to template machine screw STS Self-tapping screw Top TB Terminal block TB Through bolts TBGN Through bolts and grommet nuts TBN Through bolts and nuts TC Tin clad TD Time delay TMS or tms To Template with machine screws Top UC Undercut (door) UC Undercut head (screws); also used US and UCH UL Underwriters... See #9.
Componet - Structural
25" slots 2.4 Friction clip - Girt to jamb CL3016 Red Oxide 11 ga. 9/16" hole with 4" and 5.5" spacing includes (2) 0.5"x1.25" bolts and nuts for fastening to the jamb. 2.3 Insert girt clip CL3185 Red Oxide 3/16" plate 9/16" hole 3.0 Purlin to Purrlin clip CL3169 Red Oxide 3/16"... See #10.
Light Pole Banner Brackets
Arms at top and bottom. Item # SC Holds 1 banner per pole. Arm at top, tie off at bottom. Item # SC/G Heavy Weight Custom Brackets (1) 3/8" steel bolts and nuts per clamp (each side). 1/8"x3" steel plate formed to match shape and size of pole. End Closed with flash cap Banner top tie-off ring. 1 5/16"... See #11.
A Guide to Builders Hardware Terminology
17) Also called Self-Closing Hinges or Pivots Clamp Flange. A spring hinge flange which wraps around the edge of the door and is fastened with thru-bolts and nuts. Double Acting. When a door is so arranged to swing in either direction. Fall Mortise. When one hinge flange or leaf is mortised into the edge of the... See #12.
Sanymetal Product #1
Pilasters shall be secured to floor by means of 1/4" thick anchor bar mechanism and shall be secured and leveled by using 3/8" bolts and nuts-tension/compression mounted. 5. HARDWARE Doors: Shall be equipped with Sanymetal. See #13.
| 
