You are here:  Homepage  >  piping  >  discharge piping

Discharge piping

Please find below a selection of relevant articles from AEC companies and organizations for discharge piping. Bio-Microbics Incorporated ...flows that otherwise may scour solids out of the septic tank with the effluent. 7. Solids Exclusion Ring - This ring prevents the possible short circuiting of solids through the discharge piping. 8. Angled Slots - Angled slots, similar to those used in industrial well screens, are used because they resist blinding (clogging) better than mesh-type screening devices. See #1. NETZSCH NEMO Progressing Cavity Pumps, Positive Displacement Pumps, Sludge Pumps, Metering Pumps ...of the molasses increased due to a decrease in temperature. Shaft breakage and dramatic capacity drops were very common. Insulating the molasses tanks and heat tracing the discharge piping did offer some relief. However, it became necessary to heat the holding tanks twenty four hours a day during unpredictable cold spells. Heating the tanks became very expensive. See #2. Pumping products from Liberty Pumps ...Head and Friction Head – and is expressed in feet. Static head is the actual vertical distance measured from the minimum water level in the basin to the highest point in the discharge piping. Friction head is the additional head created in the discharge system due to resistance to flow within its components. Liberty has charts available to calculate TDH. See #3. D&D's The Rover ...power pack complete with a hydraulic reservoir, oil cooler, diesel fuel tank, fully automated safety shut down system and winch operated Axial Flow Pump with (20) twenty feet of discharge piping and (50) feet of flexible discharge hose. The trailer is highway rated and includes lighting, electric brakes, steerable front axle, lockable tool storage... See #4. Neptune Pump Manufacturing Company - MODEL HD Industrial Sump Pumps ...Curves above were developed from impartial tests using Neptune Pumps conducted by the Engineering Department of Drexel University, Phila. PA. NOTE: The use of elbows in the discharge piping will reduce the head capabilities. Consult factory recommendations. PUMP MODEL HP MOTOR TYPE PH VOLTAGE Cast Iron Brass 316 SS HD3-25-O 3/4 Open Drip... See #5. Marlow Pumps ...Handling Centrifugal Pumps Features and Benefits Back Pull-Out Design: Complete power end with seal chamber can be easily removed from casing without disturbing suction and discharge piping. Easy to sling power end makes pull-out safe and simple. No need for special tools. Back Pump-Out Vanes and Rear Impeller Ring: Reduces seal chamber... See #6. Shipco® Pumps: Wiring, Piping, and Electrical Specifications of Boilers Qty. of Pumps Option for Continuous Run Pumps Qty. of Level Controls/ Boiler Type of Standby Alternation Valve Trans- former Pump Discharge Piping & Electrical Specifications Boiler Feed Simplex Auto-off 1 1 Yes 1 None None None No 51000-A + 61B1P-N Wiring/Piping 2-page file Electrical Specifications... See #7. E/One Sewer Systems: Grinder Pump Product Catalog: Upgrade Grinder Pump The annual energy consumption is typically that of a 40-watt light bulb. The 1 1/4" slide face discharge connection is adaptable to any existing discharge piping. The internal check valve assembly, located on the grinder pump, is custom designed for non-clog, trouble-free operation. Units are available with a... See #8. 1: http://www.biomicrobics.com [c1077224] 2: http://www.netzschusa.com [c985514] 3: http://www.libertypumps.com [c925024] 4: http://www.ddpumps.com [c1036835] 5: http://www.neptunepump.com [c865739] 6: http://www.marlowpump.com [c984981] 7: http://www.shipcopumps.com [c1148806] 8: http://www.eone.com [c1171789]