_menuCloseDelay=500;_menuOpenDelay=150;_followSpeed=5;_followRate=40;_subOffsetTop=0;_subOffs...
...is used in sign shops where production speed is a high priority. This high gloss enamel is suitable for brush, spray or roll coat application. The coating will normally air dry in 15 minutes to 2 hours. It is also suitable for forced drying. Industrial Enamels are suitable for sign backgrounds. High performance industrial... See #2.
Wymark
...with RUSTROY, iron or steel surfaces quickly change in colour to deep blue or purple indicating the formation of the protective iron-tannate compound. The surface can become touch-dry in as little as 20 minutes. The dried RUSTROY coating should be painted over with protective and/or decorative paint suitable for use on metal. It is not necessary... See #3.
Concrete
...granulated blast-furnace slag, can be used to replace portions of the cement powder. Concrete Hydration Process Contrary to today’s commonly used terminology, concrete does not dry in order to harden. Made primarily of cement (discussed above), concrete hardens by gluing the aggregates together. The cement, when mixed with water, forms... See #4.
Elsro, Inc. - Installation, Protection, and maintenance
...be applied at temperatures below 40 degrees F, and should not freeze. Coverage rate is between 500 and 650 square feet per gallon, depending up porosity of floor. It should be touch dry in approximately three hours and firm dry in 24 hours. TILE FINISH Elsro Top Coat Sealer or our new Static-Free Dissipating Top Coat Sealer, are designed for... See #5.
Trouble Shooting Wood Finishes
...Strain paint before use Particles appear after spraying but not while spraying the wet film Make sure with magnifier that it is not air bubbles. Dip or pour paint on glass and let dry in enclosed dust free area. Examine film when held up to light for defects. DRY SPRAY Wrong solvent used Choose slower evaporating solvent Spray gun problems... See #6.
Nicolock - Additional Nicolock Products
Helps protect against oil, gas, salt, antifreeze, transmission fluid and dirt* Leaves a wet look with a high gloss finish. Low odor. For both indoor and outdoor use. Touch dry in 8 hours, can be driven on after 24 hours. Coverage approx. 1000 sqft./5 gal. *Based on 7-day immersion test. Download Specifications Nicolock Polymeric... See #7.
Building Dryers, Mobile Dehumidifiers (Porta Dry)
...a dehumidifier consumes, it will give out 2.5kW of heat energy. Thus by removing moisture from the air, rather than heating it to a high temperature, Porta-Dry dehumidifiers will dry in a gentle, more controllable manner. This alleviates possible material shrinkage and cracking problems associated with high temperature drying methods and... See #8.
Karnak Corporation
...A: The dry or cure time for Karnak products depends on the specific product used and the outside ambient temperature. For the most part, Karnak brush or spray grade coatings will dry in 24 hours. Karnak flashing cements and mastics, will "skin" over in 24 hours, but take longer to fully dry because they are applied at a heavier rate than... See #9.
Bathroom and Kitchen Refinishing Coatings - Top Coats
...Polymer Our BEST coating for bathtubs, tile, appliances, fiberglass, and marine applications! High gloss, UV resistance, ISOCYANATE FREE, and fastest drying in Industry. Touch dry in 2-3 minutes. 4 to 1 mixing ratio. Standard colors: White, china white, bone, almond and clear. Base Catalyst (4 to 1) $27.95/qt, 19.75/qt gal $28.95/qt in gal. See #10.
surface - how to specify
...cleansers may dull the finish and are not recommended. It is advisable to test a small inconspicuous area to ensure selected cleanser does not damage finish. Surface finishes dry in 4-6 hours, but should not be cleaned before curing is complete in 3-4 weeks. All our finishes are very durable after curing. Ordering and Shipping All of... See #11.
MGC - Masonry treatments, paints & coatings - BIOCHECK ALLWEATHER
Coverage Capacity Depending upon substrate profile and suction, typically: Porous/textured surfaces: 3-4mē per litre Non porous surfaces: 6-8mē per litre Drying time: touch dry in 1 hour, recoat 16 hours. Colours: White, Magnolia, Cream, Parchment, Maltese Stone, Dewdrop, Peanut Butter, Summer Blue, Ivory, Terracotta and Seagull. Full B. See #12.
Bondit Construction Chemicals: Product Details
Remix and apply the paste to the tile joints with sponge or towel. Surplus BONDIT TILE MATE should be removed with a wet sponge. The joint filler becomes dry in a day. Polish the tile with a clean and dry cloth. Dosage Please see "For more details" link above. Shelf Life 12 months (to be stored in a cool and dry place... See #13.
Color Wheel Paints & Coatings - Glossary
Bloom: (1) a bluish-white haze that sometimes appears on a varnish film. (2) a hazy appearance on any film, generally caused by allowing coating to dry in a poorly ventilated area. Body: viscosity, or "stirring thickness, " of an unapplied wet coating, measured in Krebs units; also, a middle- or undercoat. Bonding:... See #14.
TM Pratt & Company
Allow each coat to dry before proceeding with the next coat. Feather and gradually blend the VIELA into the existing plaster. When the final VIELA coat is dry in the repaired area lightly buff the new/old work joint with steel wool to create a mat finish. Use ‘000’ or ‘0000’ grade steel wool. See #15.
Huntco Supply - Commercial Bicycle Rack Sales
A dilute acid solution removes rust and a fluxing procedure removes oxides. Only then is the bike rack immersed in 98% pure molten zinc and allowed to dry in ambient air. The rack is then hand-filed to remove any galvanizing flash. The result is a Huntco bike rack that is virtually abrasion-resistant. Our POWDER... See #16.
| 
