AEC-CADinfo
Free Engineering Publications
Computer-Aided Design
Architecture / Engineering / Construction
News and Information on AEC-CADinfo

Directories
 
AEC Software News
 
 
 
Search
Google
web this site
News/Publications
 
Services
 
 
 

You are here:  Homepage  >  inside wall - walls  >  inside walls

Inside walls

Here's a selection of relevant articles about inside walls from AEC companies and organizations, including Floornature.com, Rumber Materials, Inc. and JOMY Inc.

Report Site

JOMY Retractable Ladder General Information
...DESCRIPTION Basic Use: Supplementary means of egress for emergency exit or rescue or for permanent roof access on outside walls where space or unauthorized access are concerns. On inside walls, provides access to rooftop hatches while being unobtrusive. Composition and Materials: Fixed and mobile vertical ladder stiles are extruded aluminum sections... See #1.

Metal-Fab, Inc. - Flexible Chimney Liners & Connectors - For use with gas-fired applainces.
...are being vented into existing masonry chimneys. If vented into a potentially oversized and unlined masonry chimney, the rapidly cooled exhaust gases are likely to condense on the inside walls of the chimney. The acidic gases will, in time, cause deterioration of the masonry chimney -- causing health hazards and costly repairs. When a properly... See #2.

Floornature - architectural news, design and information resource for ceramic tile and stone
...carcinogenic benzene when they are out on city streets: sadly, the air is polluted also inside of buildings. Scientific research has demonstrated that, among all the materials for inside walls and floors, technical ceramics are the least pollution-prone. To explain these findings, we suggest that pollution indoors is caused by benzene entering... See #3.


Com-Pak Twin Plus
...(Model CT) in the ceiling? The Com-Pak Twin Plus (Model CT) cannot be installed in the ceiling. Can I install my heater under a window or by a door? Cadet recommends installing on inside walls, however it can be installed under a window or by a door. If installed in an outside wall, be sure the heater is not blocked by drapes. Also be sure no... See #4.

Sonitec: industrial water filtration and pollution prevention: products: VORTISAND: features
...on the sand media and increases the total filtration surface area. This turbulence produces a sustained cleaning action that forces the suspended solids to accumulate on the inside walls of the tank. As a result, much finer sand can be used without any clogging problems. The water, now largely free of impurities, is then filtered through... See #5.


New Construction
...A camera inspection might be required for your project. A pipe inspection camera is available, but a sewer inspection camera might be too specialized if you need to inspect inside walls, behind appliances, etc. A great camera for an inspection would be a micro-inspection camera. Not only can it fit in tight places, but it has a digital... See #6.

Blast Bunkers by Rumber Materials made from 100 percent recycled materials and rubber
...ramps / Slips Oil Field Applications Racking Boards Trailers Matting Boards Pipe Stripping Blast Bunkers Sound Abatement Blast Bunkers Rumber boards are being used to line the inside walls of blast bunkers. Our boards protect the walls while the B.O.P. valves are tested. Bunkers are used to test up to 10, 000 p.s.i and 15, 000 p.s.i valves. See #7.

AE Staley - Wear Resistant Linings in Action
After extensive research, the company decided in 1982 to install ABRESIST® ceramic tiles made from fused cast basalt. The tiles are attached to the inside walls of the cyclone with Portland cement mortar, reinforced with a wire mesh underlay. Performance requirements for the tile liners are severe. About 210, 000... See #8.

Radon Test Kit
RADON GETS IN THROUGH: 1. Cracks in solid floors 2. Construction joints 3. Cracks in walls 4. Gaps in suspended floors 5. Gaps around service pipes 6. Cavities inside walls 7. The water supply Providing solutions to improve the quality of your home is what we do. Indoor air quality is critical to a healthy home! See #9.

Thermoplastics, Recycling and Polymers
Next, air is blown into the softened tube (similar to inflating a balloon), which forces the outside of the softened tube to conform to the inside walls of the mold. Once the plastic cools, the mold is opened and the newly molded container is removed. Blow molding is used to make many plastic containers, ... See #10.

1: http://www.jomy.com [c1885273]
2: http://www.mtlfab.com [c1751775]
3: http://www.floornature.com [c1508319]
4: http://www.cadetco.com [c1802375]
5: http://www.sonitec.com [c1613829]
6: http://www.askthebuilder.com [c1622318]
7: http://www.rumber.com [c1516735]
8: http://www.abresist.com [c1600082]
9: http://www.batticdoor.com [c1554164]
10: http://www.npiplastic.com [c1624523]


Add your web page here?
Please send your link and description (at least 20 words) to addpage@cadinfo.net. Placement is free. We reserve the right to refuse or modify your contribution.

Have your web page removed?
Please send a note to removepage@cadinfo.net. After verifying your request we'll remove all references to and images of your site.

 





Copyright © 2004-2009 Actiosoft / Digital Business Media: compilation of news, articles, white papers and web references concerning inside walls.