TCNA - Technical Services: FAQ
...developed to address special conditions or to utilize new technology. These methods will not be in the TCA Handbook but may work quite well when used in accordance with the manufacturer's instructions. To find out if any method is appropriate for certain conditions and to find out warranty and application information, you will want to speak with the manufacturer. See #1.
PowerStar Electric Tankless Hot Water Heater - Warranty Information
...accordance with the applicable local plumbing and/or building code(s) and/or regulation(s), or c) The water heater has not been installed in accor- dance with the printed manufacturer's instructions, or d) The water heater is not continuously supplied with potable water. 5. The OWNER and not the Manufacturer or his representative shall be liable... See #2.
Radiant heating installation manuals-easy to understand, pictures and diagrams.
...shows you how to make it happen! Instructions for installing the Polaris Water Heater. The Polaris Water Heater is a very sophisticated unit and it is critical that the manufacturer's instructions be followed implicitly. Please be advised, though, that you need to follow Radiantec's plumbing diagrams when connecting your system to the Polaris. See #3.
|
Q U I K - T A P E Finishing
...HOME • Two coats of compound are often recommended to finish and cover all joints, nail heads and corners. Each coat should be allowed to dry thoroughly, according to manufacturer's instructions, so that the surface does not crack and can be sanded easily. • Each additional coat of compound should extend two inches beyond the edge... See #4.
|
|
Pilot Rock Park - Camp - Street Site Equipment
...are valid ONLY if the products: a) are assembled and installed according to manufacturer's specifications and instructions; b) have been properly maintained according to manufacturer's instructions; c) have not been altered by the addition or deletion of parts, or modified in any other manner; d) have not been subject to misuse, vandalism, ... See #5.
| |
Beveled Glass Designs Finish Instrustions
...penetration; the second coat can increase this between 30% and 80%; the third coat will result in protection above 90%. Always apply the finish in accordance with the manufacturer's instructions on the label, as bonding to the wood surface and bonding between coats is critical to adequate protection for your entryway. If you want to paint... See #6.
|
|
General Specification Page
...can be used for all applicable pipe penetrations and plumbing fixture floor openings through Fire-Rated floors, walls or floor/ceiling assemblies, in accordance with the Manufacturer's instructions. You can download a pdf (Adobe Acrobat) drawing for inclusion in a specification. If you would like to download this document, please click here. See #7.
|
Trendstone Plus Ground Face Masonry Units | Trenwyth Industries | an Oldcastle Company
trenwyth.com, for mortar type and specifications. For all exterior mortar, use matching Trenwyth-approved water repellent mortar admixture following manufacturer's instructions. Consult manufacturer for recommendations. SIZES AND SHAPES Surfaces are manufactured to provide finished dimensions of 7-5/8" x 15-5/8" ± 1/8". See #8.
SafeGlide Aluminum Bolt-On Enclosed Track | Edko
All mounting hardware shall be hot-dip galvanized or plated for corrosion resistance. 5. Support Structure Enclosed track shall be attached as per manufacturer's instructions to the gate frame provided by others. Completed gate assembly shall be erected on two 4" O.D. posts of schedule 40 galvanized steel pipe weighing a minimum of 9. See #9.
DEPENDABLE SKIMFLOW ES
x ___ft. Accepted sample establishes standard for Work. Complete application when no longer needed for reference. 1.05 DELIVERY, STORAGE AND HANDLING Comply with manufacturer's instructions. Deliver in original, unopened packaging. Store in dry conditions and protect from direct sun exposure, freezing, and extreme heat (greater then 105F. See #10.
Akzo Nobel Coatings, Inc. - Polydure1000
In this process, coatings are applied to specified metal substrates that have been thoroughly cleaned and chemically pretreated in accordance with manufacturer's instructions to optimize adhesion, forming and weathering. POLYDURE®1000 coatings and primer must be baked and cured in factory ovens at temperatures ranging from 400°-480°F. See #11.
Fyre-Tec & Prime-Tec Custom Steel Windows - Rated & Non-Rated Models
ERECTION Installation of Fyre-Tec™ and Prime-Tec™ steel windows by other than factory trained representatives shall be in accordance with manufacturer's instructions and recommendations. All steel window frames shall be installed plumb, level and square without bending, twisting, or otherwise distorting window members. See #12.
General Plastics - Plastic Fittings for Heating and Air Conditioning
PVC Heat/Air Duct maximum duct temperature shall be 150 degrees F. PVC Heat/Air Duct shall be installed in conformance with the manufacturer's instructions. INFORMATION REQUIRED ON PLANS AND SPECIFICATIONS Cell class 12454 B as per ASTM D 1784 and tensil strength as per ASTM D 2412. IDENTIFICATION All Kroy Industries, Inc. See #13.
Masonry Heater Association of North America
1 Installation. A Masonry Heater shall be installed according to one of the following. 1. the terms of its listing, or 2. ASTM E 1602 and the manufacturer's instructions, or 3. ASTM E 1602 and the supervision of a skilled masonry heater builder. R1006.2 Seismic Reinforcing. Masonry heaters shall be anchored and... See #14.
|
product specifications for TRIPOLYMER
5 to 16.9 6. Fire Hour Rating ASTM E-119 - as per specific wall design C. INSTALLATION Materials shall be installed according to the manufacturer's instructions through equipment manufactured by C.P. Chemical and by a factory trained/certified insulation contractor with a current certification card. back... See #15.
| |
How To Install Kitchen Cabinets with the T-JAK Tool
Place shims at wall studs and floor, as needed, to keep cabinets level, straight and plumb. Fasten cabinet stiles and fronts per cabinet manufacturer's instructions. Install oven and/or pantry cabinet up against adjoining base and wall cabinets. When the base cabinets are installed, measure for counter top. See #16.
|
|
