|
Technical Specs Gable Buildings
...(55%) standard by a continuous hot dipping process. Coating weight shall be a minimum of 0.50 oz. of aluminum-zinc alloy per square foot of coated sheet equivalent to about 0.8 mil thickness on each side. Minimum yield strength of panel material shall be 50, 000 PSI. Wall Panel Design Exterior wall panels of the building shall be a single continuous... See #1.
|
|
Moisture-Flex Fluid Applied Weather Resistant Barrier
...cycles APPROXIMATE COVERAGE: MOISTURE-FLEX is a single component ready-to-use material available in five gallon pails (19 liters) and 55 gallon drums (209 liters). The theoretical mil thickness given for coverage per gallon is based on smooth, nonporous surfaces. Actual gallons required in the field to achieve the minimum dry film thickness will... See #2.
|
Waste Heat Recovery Systems >> Cain Industries >> Boiler Economizer, Finned Tubing, Cain...
...or cupro nickel tube to copper fin with Nickel Brazed/welded method of fin tube attachment for temperatures to 1, 750°F.* * Optional Protection: A Nickel Clad Coating, up to 2 mil thickness, is available to provide extended corrosion protection. Sample Applications Converter Cooler With spiral fin tube across the face of the radiator, the... See #3.
|
Hypalon Roof Resurfacing System & Rubber Roof Membrane / TPO Roofing - Truco, Inc.
...can occur without substantial evidence of leaks within the building. A timely diagnosis of the roof assembly, including a moisture scan and calibration of the membranes current mil thickness is recommended. Resurfacing Hypalon roof membranes with Truco's non-chalking Eterna-Seal coatings is an unobtrusive ( no down time within the facility)... See #4.
|
|
Technical Documents In Adobe(c) PDF format from Hawk Labs bathtub tile
and kitchen...
...printable and come right from our catalog. They are here as an added convience for our clients. Mixing Instructions Ratio's and More Application Procedure How to spray topcoats Mil Thickness Understanding how to use a Mil Gauge Glas-Tech 9000 Topcoat Resin Uses and properties of Glas-Tech 9000 Glas-Tech 9000 Heat Resistant Formula Uses and... See #5.
| |
|
National Roof Coaters
When properly applied, Ultracote-White's water tight seal is unaffected by seasonal movement of your building. ULTRACOTE - WHITE does not chalk or lose mil thickness and has at least one half the moisture impermeability as compared to acrylic coatings. ULTRACOTE - WHITE provides a uniform, seamless, non-penetrable covering to a metal roof. See #6.
|
|
1
Concealed/protected fasteners to be zinc coated. Anchors to be zinc coated. I. Bituminous coating: Cold-applied, asphalt mastic meeting SSPC-Paint 12, minimum 30 mil thickness. J. Neoprene pads: Neoprene, 60-70 durometer hardness, meeting ASTM D1056. 2.2 FABRICATION A. Factory fabricate skylights to dimensions and specifications... See #7.
FOUNDATION WATERPROOFING
Lucas #735 Elastomeric Foundation Coating is a polymer modified asphalt coating that is spray applied onto the foundation wall at a rate of 60 wet mils. Dry mil thickness is a minimum 40 mils which complies with the waterproofing requirements of the International Residential Code section R406.2. Lucas #735 Elastomeric Foundation... See #8.
|
Tnemec Project: Smithfield Foods Rehabilitation
Series 201 Epoxoprime, a high-solids, polyamine epoxy primer, was roller-applied and followed by a coat of Stranlok that was spray-applied at 25 to 40 mils dry mil thickness (DFT). A topcoat of Series 280 Tneme-Glaze, a polyamine epoxy, was spray-applied for improved aesthetics and additional protection against abrasion, impact... See #9.
|
|
ERITECH? Copperbonded Ground Rods
677?? 17.20 8 2.44 5 50 4.55 613400* 3/4?? 17 0.677?? 17.20 10 3.05 5 50 5.62 614400* 1.0?? 23 0.910?? 23.11 10 3.05 3 25 5.74 *UL listing requires a minimum of 10 mil thickness of copper with minimum rod diameter 0.500" and a minimum of 8 feet length ANSI is a registered trademark of the American National Standards Institute. See #10.
| |
Linetec offers flat sheet and break metal services
Some of the benefits you'll receive by using Linetec's flat sheet services are: FAST In stock Reduce freight costs by 50%. Linetec stocks 4X10 sheet in mil thickness of.040, .063, and.125. Besides our in-stock sheet, Linetec can provide flat sheets of any size and thickness. Large IHB capability Linetec has the capabilities... See #11.
|
H.B. Barrington
We apply TGIC Polyester Powders or our TGIC Super-Polyester Powders over a Zinc Rich Epoxy Primer in our 12-Stage Finish Process. This process ensures the proper mil thickness and adhesion necessary to guarantee years of beauty and service. Choose from dozens of standard colors, or we can match custom colors at your request. See #12.
|
Waterproofing: WascoSeal®
S.T.M. standards D-822 for a period of at least 400 hours. NOTE: Not recommended for use as through-wall flashing Available in 20- and 30-mil thickness, with standard widths of 12”, 16”, 18” and 24” *WASCOSEAL® is a registered trademark of Wasco Products, Inc. Downloadable data: WascoSeal®. See #13.
| |
Firefree Coatings - Testing and Industry Performance on our Fire Retardant & Fire Resistant...
From the numerous room and house burns performed by Firefree Coatings, Inc. over the last several years, the company has shown that, depending on the dry mil thickness applied to entire walls and ceilings of rooms, it can resist a fire in excess of 2000F up to two hours and thus contain fire to the room of origin. The... See #14.
|
|
www.compotite.com
COMPOSEAL Blue Vinyl Shower Pan liner comes in 40 mil and 30 mil thickness in 50 Ft. and 100 Ft. rolls as follows: 40 and 30 mil gauge: 4 ft x 100 ft 5 ft x 100 ft 6 ft x 100 ft 40 mil gauge: 4 ft x 50 ft 5 ft x 50 ft 6 ft x 50 ft COMPOSEAL Blue is warehoused in Reno, NV, Dallas, TX, Birmingham, AL, St. Petersburg, FL... See #15.
|
Pipeline Seal and Insulator, Inc.
PSI PVC Coating has been subject to a salt spray test up to the full 3000 hrs as specified by ASTM B117 method. The coating as applied in a 15 mil thickness withstood the full 3000 hrs of salt spray exposure cycled in 24 hr intervals. The coated sample is analyzed after each 24 hr cycle and results noted.... See #16.
|
