BMI Products: Mortar: Roof Mortar
...a plastic homogeneous mortar (approximately two minutes but not more than five minutes). A minimum amount of clean, potable water shall be used to produce a workable consistency. Pot life is approximately 1 1/2 hours. Coverage 50 lb. bag for clay tile - approximately 8 linear feet Specifications BMI Roof Mortar is Type N mortar in accordance with ASTM-C270. See #2.
Summitville Tiles, Inc.
...TCA guidelines for proper substrate and cure conditions. S-2000 meets or exceeds ANSI A118.4. Available in 25-pound or 50-pound bags. Temperature 60 F (15 C) 70 F (21 C) 90 F (32 C) Pot Life 40-50 min. 30-40 min. 20-30 min. Open Time 20 min. 20 min. 10-15 min. Clean Up Time 20-30 min. 20-30 min. 10-15 min. Set Time 3-5 hrs. 2-3 hrs. 2 hrs. COVERAGE: Sq. See #3.
ENAMO GRIP application - ENAMO GRIP graffiti cleaner graffiti
...still trap air bubbles that would need to be brushed out.. Catalyst ratio: This is a two-part mixture. Mixed 1 part curing agent to 3 parts base. Mix on job site before application. Pot life is 6-8 hours at 77 degrees Fahrenheit ( higher temperatures accelerate reaction and reduce pot life). Packaged unit: Shipped as a 4-gallon kit. Three gallon... See #4.
Interspan Technical Data
...Two years in original containers, stored in a cool, dry place. Flash Point: 250°F. Density: 14lbs./gal. Color: Gray Installation Temperature: Refer to Installation Manual. Pot Life: Approximately 30 minutes at 70°F. Cure Time: Can be trafficked after 24 hours @ 68°F. Chemical Resistance: Gasoline-Resistant; Diesel Fuel-Resistant;... See #5.
Bondit Construction Chemicals: Product Details
...bonding of different construction materials in interior and exterior areas. Characteristics Base Cement with modified special polymers. Colour Grey. Working Temperature 30 deg C. Pot Life 30 minutes. Other Characters Movement Absorption: Nil Advantages BONDIT TILE ADHESIVE gives an impermeable layer. BONDIT TILE ADHESIVE can be easily applied... See #6.
Grouts & Materials - Self-mix materials two
...P2 Pumpable polyester resin For bonding metal components into horizontal holes in masonry, concrete and rock. Pack Size: 2.0 litres PERFORMANCE DATA Setting times Temperature Pot life Gel time Service load time 5°C 90mins 120mins 16hrs 10°C 50mins 75mins 4hrs 20°C 20mins 40mins 2hrs 30°C 10mins 20mins 1hrs Ultimate physical... See #7.
70410 & 7430HB Cure
70410 Accelerator Amount Pot Life Pot Life Pot Life Recoat Time Recoat Time Recoat Time @40F-60%RH @75F-50%RH @95F-50%RH @40F-60%RH @75F-50%RH @95F-50%RH none none >7days >7days >7days 48 hrs 14 hrs 12 hrs 7931 4 oz/5 gal >24 hrs >24 hrs >24 hrs 22 hrs 10 hrs 8 hrs 7931 8 oz/5 gal >24 hrs >24 hrs >24 hrs 21 hrs 7. See #8.
Roofdx Copper
...§ Will not re-emulsify or wash away with rainwater § Can easily be recoated § Warrantied for 10 years SPECIFICATIONS: Coating Type: Ethylene Elastomer VOC: 300 grams/liter Pot Life: Not applicable (single component) Shelf Life: 12 months Recommended Thickness: 20 mils dry film thickness Coverage: 50 square feet/gallon (2 coats @ 100 sq. See #9.
Parex - Base Coat & Adhesive 121XL
...moisture-resistant bags Storage: Store off the ground and protect from sun and moisture. Shelf Life: Six months if protected from sun, freezing, and moisture. WORKING TIME: Pot life is 1-3 hours after water has been added. Open time is affected by humidity and temperature. DRYING TIME: Temperature must be minimum 50°F (10°C)... See #10.
Installing Joint Epoxy Sealants
...and "B" before batching the epoxy. Refer to product data sheet or packaging for proper mix ratios. Only mix the amount of material that can be used within the pot life. Mix joint filler using a low speed drill with a mixing paddle (never mix by hand). Scrape the sides and bottom of the pail while mixing. Remember, large... See #11.
Heresite VRL 500 SERIES LOW VOC AIR DRY PHENOLIC
We list over 500 different chemicals that our air dry phenolic VRL-500 will resist. It is especially effective in salt air atmospheres. User friendly- one component, (no pot life problem)-2 year shelf life. Low flame spread characteristics Used to protect fans, duct, cabinets, coils, fume hoods and all types of plant equipment. Has... See #12.
DURABAK Spec Sheet
5 Fire resistance Flame spread ASTM E-162: 01 Smoke generation ASTM E662: 06 Salt water resistance 100% Freeze-thaw resistance 60 F to +254 F Pot life 3 hours Shelf life min. 1 year Flash time 1½ to 3 hours Walk time 6 to 12 hours Time between coats ± 1 hour Full cure ± 4 days VOC 2.08 lbs/gal DOT Hazmat Info. See #13.
Stainless Steel Coatings - Low VOC
Available in a choice of two gallon or two quart kits, both the primer and finish are user-friendly coatings with excellent wetting characteristics and long pot life. They may be applied by a wide variety of techniques, including brush, roller, conventional airspray, airless and air-assisted airless applications. Protects... See #14.
ELASTRON - UNITED COATINGS
ELASTRON cures by chemical reaction to form a highly impermeable, elastomeric membrane that also offers excellent chemical resistance. ELASTRON is a pot life system designed for application through standard airless spray equipment or by brush or roller. BASIC USES ELASTRON was developed primarily for application... See #15.
Lime Plaster for Wall & Faηade Treatment
Plastering & stucco contractors praise their highest productivity and excellent workability. Smooth, monolithic finishes can easily be achieved whatever the surface area. Pot life and setting times adequately contribute to better efficiency and reduced waste on the job site. Sitemap Print. See #16.
| 
