|
surface - how to install
2. Scratch/Base Coat: Mask off areas around the work surface. Skim properly prepared work surface with Surface Scratch Coat using full nap roller and level continuously with steel trowel during roller application to an even thickness and uniformity of aggregates. Allow to dry overnight or a minimum of 4 hours before sanding and application of next step. See #1.
|
|
SCHUNDLER COMPANY--Lightweight Sound-Deadening Perlite Concrete
...place and lapped to prevent leakage onto the sub floor. Finishing: Finish will be as specified by owner. Normally a steel float finish is satisfactory for carpet and pad, while a steel trowel finish is necessary under resilient or sheet flooring. Up to 2% of Calcium Chloride may be used to accelerate finishing time. CAUTION: Calcium Chloride... See #2.
| |
|
Elsro, Inc. - Installation, Protection, and Maintenance Products
...Add Patch-All powder to water and mix for at least 3 minutes with a drill mounted mixer. APPLICATION Place Patch-All with a trowel. When Patch-All starts to obtain initial set, steel trowel to desired finish. ELSRO ADHESIVE DESCRIPTION Elsro Adhesive is a non-toxic, non-flammable, rubberized asphalt emulsion. USES Elsro Adhesive is designed... See #3.
|
|
Dynaflex Application Specification for Concrete - 02792
...all new concrete to cure at least twenty eight (28) days prior to coating. 2. Thoroughly clean entire surfaces to be coated. 3. Light broom finish of new concrete is preferred. Steel trowel finishes are not acceptable for this application. 4. Vapor barrier must be placed prior to installing concrete slabs. 5. Inspect slab for birdbaths one... See #4.
Bondit Construction Chemicals: Product Details
...with an rpm 350-400 for about 3 minutes till a Homogeneous mixture is obtained. The mixed material should be spread onto the well prepared surface to a uniform thickness by a steel trowel. The material should be compacted and finished with a wooden trowel. Dosage 2.5 sq.m. per 16 Kg at 3 mm thickness; 1.5 sq.m. per 16 Kg at 5 mm thickness. See #5.
General Polymers Overview
...rich aggregate results in the formation of a swelling gel. The resulting pressure will eventually lead to cracks in the concrete. The concrete should be finished with a light steel trowel. Over finishing the concrete will only bring additional past to the surface, which does not offer a strong, bonding surface. Best results are obtained... See #6.
IPA Systems
4 mm) in single applications. Thick coatings should be built-up in layers for best results. OCTOSKIM may also be applied in skim coat application and feather edged with a steel trowel. Feather edges should not be applied in areas exposed to vehicular traffic. Mixing: OCTOSKIM as it is packaged is a complete kit. Nothing other than the... See #7.
|
Perucchetti Marmorino Plaster Finishes
The Perucchetti specialist marble dust finishes are applied by a steel trowel in several (four to six) fine layers. The method of application and ingredients used vary slightly depending on the required finish. The recipe is a personal formula which is basically a combination of cement, lime, marble dust, pigments, oils, soap and waxes. See #8.
| |
|
TM Pratt & Company
Consult TM Pratt for appropriate primers. Application: The Viela finish is pre tinted and is designed to be applied in three or more separate coats using a stainless steel trowel. The customer may choose to apply a light wax coating after the final coat to add protection and add sheen. See separate details for compatible wax procedures. See #9.
|
|
|
Acrylic Ad-Mix 101 Guide Specifications
Mix to the proper workable consistency for troweling. Do not use a high speed mechanical mixer because this will entrain excessive air. Place the topping mix using a steel trowel, and spread to desired thickness. 3.2.2 Application of Modified Portland Cement Plaster (One Coat Work to Concrete) Use one part Acrylic Ad-Mix 101®... See #10.
|
|
Tennis Court Colored Crack Sealer (Trowel Grade)
This is an easy-to-use, trowel consistency, acrylic formulation. Application for Cracks: Clean crack and fill with TENNIS COURT CRACK SEALER using steel trowel. Wet trowel with water to facilitate application. Cracks deeper than 1/4" should be filled in multiple coats, allowing overnight drying between applications. See #11.
| |
Elastizell - Products: Floors - Rehabilitation Systems
Flooring Base Elastizell floor fills provide a smooth, solid base for applying new floor coverings. For glue down carpet or resilient flooring, a steel trowel finish is recommended. (refer to General Construction Notes ) Sound Control Elastizell floor fills improve the sound conditioning of older floor systems. See #12.
|
Creom Uk Ltd.
Granite chips may be added to bulk out the Creom CL Smoothlay Latex. Application Pour mixture onto the floor area and spread evenly using a steel trowel. Creom CL Smoothlay Latex will settle across the floor levelling out hollows in the sub floor. A spiked roller may be used to assist application if required. See #13.
TECHNICAL (5)
...be to the tolerances required on the finished floor. ii) Granwood operatives supply, mix and apply cementitious, water resistant ceramic tile adhesive using a notched, solid bed steel trowel. USE THE FOOTPRINTS TO NAVIGATE THE SITE. See #14.
Pool Trowels, Stainless Steel Trowel, 10", 12", 14", 16", 18", 24"
de click aquí para ver en es ESPAÑOL Florida: 954-973-4528 / Out of Area: 800-952-5980 / Fax: 954-973-4926 2000 Banks Road - Margate, FL 33063 E-mail: sales@advancedsurfaces.com Mon - Fri 7:30 AM to... See #15.
|
