Flashing for Masonry Walls
...droppings, the system's unique teardrop shape does several things differently: By presenting a sloping surface to mortar droppings, Termi-Net™ deflects droppings from the inside wall and causes them to accumulate at the inside face of the exterior wythe. Because the base of the teardrop is flexible, Termi-Net™ can be pushed down... See #5
Polycell - Help, Advice, Tips
...sanding? The sandpaper always clogs up and stops working. How do I paint skirtings without having to take up the carpets? How do I fill gaps between my window wooden frames and inside wall? When sanding paint and plaster indoors, the room gets thick with dust - is it dangerous to health? What type of filler should I use to make good all the... See #6
Waterproofing and Dampproofing your projects.
...that is used with Volclay bentonite waterproofing systems to detail at membrane terminations, around penetrations, over grouted concrete form-tie holes, and provide fillets to inside wall corners. Data Sheet Volclay WB Adhesive - are a water-based latex adhesive used to secure Volclay Waterstop-RX into position for all installations. Data... See #7
FIBER-GUARD®/CORRUGATED NONMETALLIC HDPE CORRUGATED CONDUIT
The corrugations provide excellent crush resistance for long term protection of delicate optical cables. Internal corrugations reduce surface contact between the inside wall of the conduit and the cable jacket, lowering friction while protecting the cable from high tensile stress during installation. Fiber-Guard/CR is available... See #8
Tilt & Turn Operation
Turn Position Turn completely open, left or right, for egress/regress or for easy claning. Depending on the position of the window in relationship to the the inside wall, they can be opened up to 180 degree, completely against the inside wall. For Ease of Cleaning: By swinging the window inward into the room, a homeowner... See #9
Robinson Fans - industrial fan, ventilation fan, blower
FC fans are also offered with an insulated plug and non-insulated housing. In this type of construction, the non-insulated housing is usually mounted on the inside wall of the furnace or oven. All Robinson FC Series are available in fan arrangements 1, 2, 4, 8 and 9. Flexibility in design also allows Robinson to offer... See #10
Measuring Tips
Bath Enclosure Measuring Tips Use a carpenter’s folding ruler with a slide to assure the most accurate measurement from inside wall to inside wall when measuring for the overall front opening. Be sure to take 3 width measurements. Bottom, top, and middle. It is important to establish the range of the overall width... See #11
A Peerless variety of Metal Door Speakers.
Flush-mount types use a rear standard steel single-gang box which is also supplied. Back box size: 2.5 in. W x 4.12 in. H x 2.43 in. D. Back box goes inside wall rough in. These Doorphones can also be mounted on a post or gooseneck at gated driveways. See them here. Doorphone operation with Ultimatoll systems here. See #12
ADS - Surface Drainage Structures (Nyloplast®)
( PDF ) Nyloplast ® Snout ® Structure The Snout Structure is a Nyloplast is a catch basin with a plastic composite hood attached to the inside wall fo the catch basin structure. ( PDF ) Nyloplast ® Weir Structure The Weir Structure is a Nyloplast catch basin with panel or plate device secured inside the structure. See #13
7GP Application Instructions
Dump the entire batch to empty the mixer and avoid leaving any old mix to be included in the next new batch. MIXING NOTES 1. Scrape the inside wall of the pump hopper as it empties to avoid build-up. 2. Wait until enough material has been pumped out of the hopper to allow sufficient room for the addition... See #14
Tin Ceilings from American Tin Ceilings: installation / crown
A piece of C1m is installed on the outside wall. C1m is factory mitered for outside corners. A piece of standard C1 is installed on the inside wall. A piece of C1c is installed on the compound wall. C1c is factory mitered on one end for inside corner coping. The profile of the outside wall C1m is traced... See #15
Sutong cable stayed bridge, strand jack lowering of 2800 tonne steel pile cap form
...4 jacks Strand jacks were mounted on temporary cantilever frames, evenly spaced around the perimeter of the caisson, and were connected to temporary jacking brackets welded to the inside wall of the caisson. See #16
| 
