Cem Flex from Target Fixings Ltd
...where access and working times are restricted. Performance Requirements Because of their method of installation it is not possible to perform random non-destructive site tests. Bond strengths can, however, be checked prior to the full installation programme. An overlong tie can be installed as normal leaving a short length (50-75mm) proud of the surface. See #1.
|
AllDeck.com
5% Plywood Substrate/ -4.7% Concrete Substrate/ -0.9% Tensile & Elongation Test, ASTM D 751 Post Accelerated Aging Average Procedure D-10202.0- 5.9 Procedure E - 7435.4 - 4.98 Bond Strength Test, ASTM C297 Post Accelerated Aging Plywood Average: Procedure D: Ultimate Load 934.86 Bond Strength 103.89 Procedure E: Ultimate Load 827.23 Bond Strength 94. See #2.
|
|
Plaster-Weld Performance Properties
...Performance Properties Performance Properties Data obtained from tests conducted periodically by leading independent laboratories. Test reports are available upon request. Tensile Bond Strength: ASTM C-631 (pulling apart bonded cement briquet halves). In all cases failure occurred in the cementitious material, not in the bond. 385 psi. Avg. 28 days. See #3.
|
|
Hydrophobic(R) - Urethane Grout Technologies - PYCOSA Chemicals, Inc
...° F ASTM D-93 Appearance Clear Liquid Cured Tensile Strength 386.1 KPa (56 psi) ASTM D-3574 Test E Density 1, 074 kg/m 3 (8.96 lbs/gal) ASTM D-3574 Test A Bending Strength 213 psi Bond Strength 99 psi 255 psi (shearing) Shrinkage 0% ASTM D-2126 Toxicity Non-Toxic Storage Store in dry areas using original container. Keep away from water and humidity. See #4.
|
Akona - Delivering Quality Solutions
...tensile, flexural and compressive strength of unmodified concrete, mortars, patches and grouts. Uses: Advantages: Use with mortars, patches, grouts and underlayments When improved bond strength, freeze-thaw and salt resistance and water permeability is desired Substantially improves bond strength and adhesion Versatile when using with mortars, ... See #5.
CAMIE 100 PRODUCT DATA
...High Performance Mist Spray Adhesive is a fan mist spray adhesive similar to Shelby ® General Purpose Mist Spray, but formulated for the demanding applications that require better bond strength and lower soak in. This premium product will adhere most all common substrates i.e. foam, carpet, paper, cardboard, felt, cloth, painted surfaces, wood... See #6.
|
Tile FAQ's
...an Epoxy Thin-Set mortar in white for mounting the textured glass tile in any application. This adhesive should be readily available in most areas, and has exhibited superior bond strength without damaging the SingleStep white backing on the tiles. You should use a grout specifically formulated for use with glass tile. Tiles can be cleaned... See #7.
| |
Polycrete II
As the material begins to cure, lightly trowel to the desired finish. Polycrete II Physical Properties TEST METHOD REQUIREMENTS Gel Time, Min. Tex-614-J 1 min. - 60 max. Wet Bond Strength to Concrete, psi Tex-618-J 250 min. Compressive Strength 24 hr. psi ASTM C 579 2, 000 min. Compressive Stress @ 0.1 in., 7 days, psi Tex-618-J 2, 000 min. See #8.
|
IPA Systems
...Strength (ASTM C 109): 1 day 7 day 28 day 3050 psi (21.0 MPa) 6500 psi (44.8 MPa) 10, 000 psi (69.0 MPa) Flexural Strength (ASTM C 78): 28 day 990 psi (6.8 MPa) Slant Shear Bond Strength (ASTM C 882): (no epoxy at bond interface) 7 day 28 day 800 psi (5.5 MPa 1850 psi (12.8 MPa) Length Change (ASTM C 157): 1 day 7 day 28 day Air Cure 0. See #9.
|
Dexotex
Tensile Strength ASTM D638 3, 400 psi (run at 2"/minute using "C" die for ASTM D-412) 4. Flash Point ASTM D92 143°F 5. Water Absorption MIL-D-3134 & ASTM D570 0.3% 6. Bond Strength ACI 403 525psi (100% failure in the concrete) 7. Impact Resistance MIL-D-3134, Para. 3.15 No cracking or loosening, Indentation 0.005 in. 8. Indentation... See #10.
|
Flextile, Ltd.
...of porcelain tile and all types of tile directly over exterior grade plywood on interior dry surfaces. Available in Grey & White. FEATURES Improved flexibility and bond strength Easy to use - just mix with water and apply Excellent workability Non-Flammable Water resistant when cured Rated as a light performance commercial and... See #11.
Type HC Hard Clad
...WHICH TURNS TO STEAM AND RETARDS HEAT TRANSFER. Physical Characteristics of Type 7HC TM Property and Test Method Value / Result* Applied Density, ASTM E-605 57 - 65 pcf Bond Strength, ASTM E-763 Exceeds Fireproofing Penetration Resistance, ASTM C-569 750 psi Compressive Strength, ASTM C-354 450 psi at 10% Hardness, ASTM D2240 50 *... See #12.
flex-dek - flexible epoxy coating
For more on chemical resistance see Chem-Dek Physical Properties Tests results based on American Society for Testing Material For important information on bond strength of concrete and epoxy click here Tests Results Compressive Strength(ASTM-D-695) 12, 000 psi Tensile Strength(ASTM-D-638) 5200 psi Flexural Strength(ASTM-D-790)... See #13.
Links to Technical Information
Links to useful technical information on galvanized rebar: American Galvanizers Association Service Life Chart for Hot-dip Galvanized Coatings Bond Strength Comparision Chart for Black and Coated Bar Specifiers' Guide to Rebar (.pdf file 324k) (Courtesy of the American Galvanizers Association) Galvanized Steel Reinforcement... See #14.
|
Mer-Krete Systems 150 Acrylic Latex Thin-Set and Grout Additive
Mer-Krete™ 150 Acrylic Latex THIN-SET AND GROUT ADDITIVE is a compounded and stabilized latex additive to improve bond strength, water resistance, compressive strength and other physical properties of cement/sand mixes as well as grouts. These mixes may be applied from a feather edge up to the needed thickness. See #15.
|
Spotlight: RBC-558-AR High Strength, Fast Setting Adhesive - RBC Industries
When speed is important and bond strength imperative, consider RBC-558-AR your solution. This epoxy based adhesive provides superior bond strength while. See #16.
|
