|
PolyWall from Parkland Plastics - 800-835-4110 - Mold-resistant, waterproof
panels made...
...locker room showers, and commercial restrooms. INSTALLATION INFORMATION Install over an unfinished, smooth, sound wall with moisture-curing, non-flammable latex adhesive using a notched trowel. When installing over a non-porous surface, such as a painted wall or ceramic tile, our proprietary Parkland Panel Adhesive is strongly recommended. Precondition... See #1.
|
Pryamid Sports Floor Systems - SportFlex
...the adhesive and installation of the flooring products and follow the appropriate instructions. Application: Porous and Non-Porous Substrates: Application: 1/8" x 18" x 3/32" U-notched trowel. Coverage - approximately 85 sq. ft. (7.9 m2) per gallon. Warranty Limited 5-year wear warranty. For complete details, contact Pyramid Sports Floor. Maintenance... See #2.
|
Treadmaster Floor Preparation Guide
...will only have approximately 45 - 60 minutes in which to spread the adhesive and lay the covering before the hardening begins. Pour the adhesive onto the floor and spread using a notched trowel. Notches should be approximately 1.5mm deep at 5 mm between centres. Care should be taken to spread the adhesive evenly. Lay the Treadmaster onto the... See #3.
|
|
Glass Mosaics - Frosted Dimensions
...for glass tile applications contact your local thinset/mortar supplier. To prevent darkening of the translucent tile color, we also recommend a white thinset. Use a 3/16 inch V-notched trowel; roughly distribute the setting material as needed onto the substrate. Use only enough setting material that can be covered in 10 minutes. Smooth using... See #4.
|
|
WECork - Products: Floor Underlayment: Cork Underlayment Installation Instructions - Your...
...a good quality indoor/outdoor carpet adhesive. APPLICATION 1. Subfloor must be structurally sound, level and clean. 2. Spread out mastic on subfloor with flat side of a 3/16- v-notched trowel to achieve good bond. Then, Use the notched side for a good bond to WECU. 3. Install WECU butting seams and up to walls snugly. 4. Roll over WECU with... See #5.
|
Schluter-KERDI - Schluter-Systems
...soluble and should be protected from the moisture in the thin-set mortar used to install KERDI. Q. What size trowel should I use to install Schluter-KERDI? A. A 1/4" x 3/16" V-notched trowel is recommended. Mix your thin-set mortar to a fairly fluid consistency (but still able to hold a notch) and solidly embed the Schluter-KERDI into the... See #6.
Scottdel - MultiBond Installation Guides
Complete the seam after applying adhesive up to the seam tape in step #5. Click here for recommended types · Important: use seam sealer. · With the appropriate notched trowel apply an approved* permanent soft-set adhesive on the Multibond cushion. · Observe open time for adhesive used. This is very Important: 15 minutes... See #7.
Mer-Krete Systems
...approximately 15 minutes, and then remix before using. Remix without adding additional water or powder. Mortar consistency shall be such that when applied with the recommended notched trowel to the substrate, the ridges formed in the mortar do not flow or slump. During use, stir mortar mix occasionally. Do not temper with additional water. See #8.
|
ATC: Core Adhesives
...Core-Bond B73 utilizes the lower viscosity Norac Benox L40LV for the gun application. B73 is "splattered" on to the fibreglass surface by the gun and spread with a notched trowel to achieve uniform minimum 1/32" thickness. The pump application of Core-Bond B73 eliminates hand mixing of the catalyst into the Core-Bond thus... See #9.
| |
Total Wall EIFS and Stucco
...at grade on Insulated Concrete Foam Block construction (ICF) Issue #1020 Using T-WALL LASTIC and Textured T-WALL LASTIC Issue #1021 EIFS vs. Traditional Stucco Issue #1022 Notched Trowel Selection for Applying TOTAL WALL Blue Mastic Adhesive Issue #1023 Using TOTAL WALL Finish over Urethane Base Coat Issue #1024 TOTAL WALL Finish Coat... See #10.
|
TredMor Adhesive System - Standard Installation
** ADHERING CUSHION TO FLOOR Pressure Sensitive Adhesive: The use of a pressure sensitive adhesive, applied with a 1/16" width x 1/32" depth x 1/32" spacing notched trowel to insure evenness of the application, is suggested for attaching the cushion to the floor. A short nap paint roller or the back of a trowel can also... See #11.
Buckingham-Virginia Slate Corp.
...Specify grade-A unfading blue-black Buckingham slate floor tile, natural cleft face with gauge rubbed bottom for thinset application. Use thinset mortar applied with a notched trowel. Type: Patterns of rectangle and squares with clean sawed edges. Natural Cleft face and gauge rubbed bottom. Sizes: Nominal sizes 6" x 6" to... See #12.
Mer-Krete Systems
Remix without adding additional water, latex admixture or powder. Mortar consistency shall be such that when applied with the recommended notched trowel to the substrate, the ridges formed in the mortar do not flow or slump. During use, stir mortar mix occasionally. Do not temper with additional admixture or water. See #13.
Mould Growth Consultants - SEMPATAP TEXTURE
4. Roll up cut length of SEMPATAP TEXTURE with foam facing out. 5. Apply SEMPATAP ADHESIVE with serrated SEMPATAP ADHESIVE SPREADER, or suitable notched trowel to wall/ceiling surface. Only apply adhesive to one drop length area at a time. 6. Hold the rolled-up piece of SEMPATAP TEXTURE in one hand and unroll... See #14.
Superior Grip Safety Surfacing - Superior Epoxies & Coatings, Inc.
4. Apply to floor immediately after mixing by pouring the mixed material over the surface and spreading it uniformly with a brush, roller, or notched trowel @ 100 square feet per unit Mixed SUPERIOR GRIP has a working time of 30-45 minutes @ 75°F. 5. Sprinkle silicon carbide granules evenly over the surface... See #15.
Elsro, Inc. - Installation, Protection, and Maintenance Products
ft. /gallon depending on the porosity of the substrate. INSTALLATION INSTRUCTIONS Stir thoroughly before use. Apply using a 1/16 inch notched trowel. Apply tile into tacky, but not wet adhesive. Use mineral spirits for clean up of dried adhesive and water for uncured adhesive. ELSRO TRANSITION STRIPS... See #16.
| 
