Georgia-Pacific Plywood Exterior Siding
...is constructed of thin layers of veneer, cutting plywood with a power saw can be challenging. Even if you use a plywood blade with small teeth, the thin outer layer of plywood ( face veneer) can tear. This may not be a problem if only the "good face" (show face) will be seen. Place the good face downward when using a circular saw and upward when using a table saw. See #2.
Algoma Hardwoods
...Finishing Instructions 8 General Policies and Procedures 9 Building Codes for Fire Safety 11 All About Wood Fire and Smoke Doors 12 Types of Veneer Cuts 13 Veneer Matching 14 Door Face Veneer Standards 15 Comparison of Flush Door Costs 22 Door Weights and Square Footages 23 Form for Presenting Loss/Damage Claim to Carrier 24 Doors Mineral Core:... See #3.
Gaco Western - GW-14-U Specification for Urethane Rubber Coating System
...of the The Engineered Wood Association - APA EXT or APA AC EXT are acceptable. Underlayment grade plywood (APA AC EXT Underlayment) with solid, plugged cross bands under the face veneer are recommended for commercial installations. Refer to General Instruction, Section GW-2-3 for complete information on the installation and fastening of plywood. See #4.
General Veneer Manufacturing Co. Hollow Core Doors
...All flush veneered Hollow Core doors shall be GENEERCO Institutional Hollow Core Doors or GENEERCO Royal Flush Hollow Core Doors as manufactured by General Veneer Manufacturing Co. Face Veneers: Face veneers shall be standard thickness, thoroughly dried, and of the species, cut and grade specified. Faces shall be book matched unless otherwise... See #5.
ALLMAR INTERNATIONAL - Medium Duty Hollow Core Hardwood/Hardboard Door
...opening 8'0" x 10'0" (2438mm x 3048mm) For 1 3/4" (44mm) door thickness standard, 1 3/8" (35mm) available Stiles consist of softwood edge, solid hardwood outer edges matching face veneer are available Rails consist of mill option wood, matching wood rails available upon request Pregraded faces: hardboard, medium density overlay, or premium... See #6.
Premium Bonded Doors - GRAHAM
..."C" Label 45 Minute Fire Door Premium Grade Construction Mineral Composite Core Stile/Rails Bonded to Core 1130 lbs. Stile Screw Holding 250º F Temperature Rise Stile Faces Match Face Veneer GPD FD 60 FD-60-7 Georgia Pacific "B" Label 60 Minute Fire Door Premium Grade Construction Mineral Composite Core Stile/Rails Bonded to Core 1130 lbs.... See #7.
Flexible wood veneer, exotic & domestic species
...veneer, 10 mil, sanply, sanfoot, realtec, lumber, wood, architectural panels, plywood, wood wallcovering, flitch veneer, oak, maple, burl, mahogany, cherry, rosewood, marquetry, face veneer, fiddle back, curly, flat cut, rift cut, quarter cut, exotic wood, exotic veneer, whittelsey, architectural veneer, furniture veneer, birds eye, inlay... See #8.
Ambico - Our Products ->Engineered Doors (Bullet Resistant Wood - Technical Specs)
...proprietary bullet resistant core. A wood veneer of plastic laminate shall be applied to the core. Visible wood stiles and wood rails matching the species of the face veneer shall be applied to the finished door panel. All tolerances shall be in compliance with ANSI/NWWDA standards. 2. 2 Fabrication. 1 General: A. Frames and... See #9.
newconstruction
Stiles - 1 3/8" Lock and Hinge edges are 1 3/8 inches wide, laminated hardwood or SCL(Structural Composite Lumber) compatible with face veneer. No finger joints used on exposed edges. Crossbands 1/16 inch wood or composite wood fiber laminated to the face and core. Laminate plastic faced doors... See #10.
|
