|
Eb-Ty Hidden Deck Fasteners: Calculator
...you can see the total number of EB-TY Hidden Deck Fasteners required for your project. Dimensions Enter Number Square Feet Total Number of Fasteners Needed 3.5" boards w/12" on center joists 0 5.5" boards w/12" on center joists 0 3.5" boards w/16" on center joists 0 5.5" boards w/16" on center joists 0 3.5" boards w/24" on center joists 0 5. See #1.
| |
INSTALLATION INSTRUCTIONS FOR ALUMA-FOIL HD AND ALUMA-FOIL PLUS RADIANT
BARRIERS
...between the two pieces of RB at the ridge or peak (Fig. A). This allows proper ventilation of your attic area. (Fig. 3 below) 3. Staple the RB approximately 6" - 8" on center on all wooden members using a 1/2" or 9/16" crown staple with 1/4" or 5/16" leg. (C) 4. It is not necessary to overlap the product or tape the seams. See #2.
|
Glassblock | Inner
The use of accelerators and/or acid washing is not recommended. Nine gauge ladder type reinforcing is to be used in horizontal joints with maximum spacing of 16 inches on center. Glass block panels are to be framed and anchored at head and jamb locations with either a channel type restraint or with PC panel anchors that give the wall a much cleaner look. See #3.
Installation
...1-1/2", 2", 3", 4", 5", and 6" can be specified. Studs can also be specified for alignment with brick or block wall mortar joints. (Brick: 2-5/8" on center; Block - 8" on center). Pad Installation Pads are plastic disks on the rear of letters. Letters are secured to the wall with silicone adhesive. Adjustable... See #4.
Thresholds - Dawson Doors High quaility Custom Stainless Steel Doors, Custom Bronze Doors, ...
...or 1/2" high, up to 120" long (one piece), to any specified width. Finish is #4 Satin. Woodscrew and rawl plug type fastener preparation is approximately 16" on center. Hardware preparation, return miters and door jamb notches are available. #4 Satin Stainless Steel #4 Satin Brass The above photos are representations of our finishes. See #5.
EnerBlock Tables
06-388-03 9.4 8.9 7.9 6.1 5.4 4.7 8.3 7.9 7.1 5.6 5.0 4.4 8" cmu with barrier and grout: 2" barrier in grouted cores 1¼" barrier in grouted cores 48" on center 8.1 7.7 6.9 5.4 4.8 4.3 7.2 6.9 6.2 4.9 4.4 3.9 24" on center 7.1 6.8 6.1 4.9 4.4 3.9 6.4 6.1 5.5 4.4 4.0 3.6 10" cmu with barrier only NCMA evaluation no. See #6.
Benefits
...less gas consumption, reduced total job ost Rebendable Hangers = Minimal waste Minimize Workmans Comp Claims 1 Product for different truss systems- adjusts from 16" to 24" inches on center & different insulation depths 6" to 15" inches deep Make retrofits and crawlspaces easy to insulate Our customer support team helps ensure maximum... See #7.
|
Tin Ceilings from American Tin Ceilings: installation / nailup
...Nailup tin ceiling panel hasn't changed in 130 years and is commonly what most retailers sell today. It requires a plywood substrate or furring strip grid spaced twenty-four inches on center. The grid must run both directions to support nailing every six inches on all four sides of the Nailup tin ceiling panel. The Nailup tin ceiling panel has... See #8.
|
METAL BUILDING KITS BY VALUE STEEL
...will require heavy machinery to lift the large beams into place. Renting a crane by the day is extremely expensive. Our steel truss systems are light and spaced every 4 or 5 foot on center depending on model. This makes the trusses easy to install without any need for cranes or heavy equipment. Just ladders and hand tools are required. I-beam... See #9.
|
Corner-Step Ladder - St. Paul Corrugating
...or rungs shall have an inside width of at least 12 inches (305 mm), shall project at least 3 inches (76 mm) from the wall and shall be spaced not more than 18 inches (457 mm) on center vertically for the full height of the window well. Home | Our Company | Products | Info Center | News | Links | FAQ | Contact Us 700 39th Ave NE Columbia Hts. See #10.
|
Main balusters are # 303 (5/8") square steel bar, with center balusters # 335 (5/8") square...
The handrail is a # 242 (2") round oak. The main balusters are # 303 (5/8") square steel bar, with center balusters # 335 (5/8") square steel bar. The balusters are spaced 6" on center and each baluster has a 5/8" square bronze shoe. The treads are a # 120 (12 gauge) pan type steel and the wood overlay is # 140 (1") oak. The center column... See #11.
Innovation Industries Inc. - FAQ
Here is a chart showing our different pushbutton styles. If your pushbutton is mounted in a traditional wall box, it will be attached to male weld studs two inches (2.0”) on center. If it is in a surface-mounted housing, the housing projects 1.375” from the wall, and the stud pattern is diagonal. Download Pushbutton Styles -... See #12.
SCAFCO PONY WALL
Home | Site Map | Request Info mmLoadMenus(); Pony Wall Upright Support: 2 each 250S162 54 Mil steel studs welded face to face. One foot on center. These are produced from Galvanized Grade D steel. Height Varies as Required Base Plate: 3 gauge Galvanized Steel, Grade D, welded to the upright support. 3 3/8" wide... See #13.
ProWay 4' Aluminum Fence and Gates
Sections are shipped fully assembled. Posts and gates are sold separately. Fence height ordered is actual length of pickets. Post spacing is 72-1/2" on center. Sections can rake about 12" over their 6' span to accommodate sloping lots. Post prices include caps. Available in 3 colors: White, Black or Bronze. See #14.
Lazy Tong Folding Gates - Miller Wire Works
LAZY TONG FOLDING GATES
Constructed of 3/4" x 3/8" channel riveted back to back, with brass washers between, not over 6" on center. Vertical end bars are cold rolled box track section with ball bearing rollers for smooth operation. See #15.
On Center Software: Construction Estimating Software & Takeoff
Since 1988, On Center Software has been developing construction estimating software and takeoff solutions to help residential and commercial construction companies estimate and submit bids in a faster, more organized, and more accurate way. See #16.
| 
