Why Buy Storm Windows
...needing to replace your current windows. Storm windows not only enhance your personal environment, they also add new comfort and security to your home. What Improvements in the R-Factor Rating Can I Expect? "Windows are a primary source of heat loss because they are both a poor thermal barrier (R factor of only 0.89) and often a source of air infiltration. See #1.
|
AIR-SHIELD Moisture Barrier
...and infiltration, reducing condensation within the wall assembly and increasing efficiency of a building’s mechanical system. Wet insulating materials lose much of their R-factor performance characteristics, reducing the energy efficiency of the structure. W. R. MEADOWS thermal and moisture protection products play a key role in maintaining... See #2.
| |
|
Fireslate: Frequently Asked Questions
...FIRESLATE Return to Top TECHNICAL SPECIFICATIONS FIRE HAZARD CLASSIFICATION: (ASTM -E-84) (UL 723) FLAME SPREAD 0 FUEL CONTRIBUTED 0 SMOKE DEVELOPED 0 K-FACTOR 2.25 BTU's-FT/HR-FT-R R-FACTOR 22HR-F-FT/BTU'S DENSITY 100 LBS/PFC MODULUS OF RUPTURE 3150 PSI TENSILE STRENGTH 500 PSI BRINELL HARDNESS 18 COMPRESSIVE STRENGTH 7200 PSI SCREW HOLDING... See #3.
|
|
What Is Expanded Polystyrene?
...range of densities to yield the necessary properties to meet the highest insulation specifications at the lowest cost. RayLite (1.0 pcf) provides a typical R-value of 3.85 per inch (R-factor + 0.26) at a mean temperature of 75F (R = 4.17 per inch at 40F). Because of its cellular structure, the R-value of RayLite is permanent. It will operate... See #4.
|
Concrete Block Insulating Systems (CBIS)
...K-Factor, Korfil, Load Bearing, Masonry, Molded Inserts, Molders, Mortar, Mortar Joint, NCMA, NECMA, NFPA, Plastic Foam, Polystyrene, Pre-insulated, Reinforced Masonry, R-factor, R-value, Single Width, Single Width Insulation, Single Wythe, Single Wythe Insulation, SPI, Structural Masonry, Styrofoam, Thermal, Thermal Bridging, Thermal... See #5.
|
|
U.S. Rubber Survivor Rolled SportFloor
.329-.35g loss Flammability ASTM D2859 Pill Test, excellent value of 3.6 (passes Class II fire requirement) Acoustics Rates superior Chemicals Resistant tomost acids and chlorine R-Factor R-8 Johnson unions measurable per (?)" in thickness VOC's No measurable units *For heavier maintenance we recommend Taski® Wiwax which is a unique... See #6.
|
STOVES - Woodstove, Fireplace and Patio Shop
Other factors that require consideration: Ceiling - height, type (flat, cathedral etc.) Windows - single pane storms, thermopane or Triple E Insulation - walls, floor, ceiling and R-factor Intended Use - primary or supplemental heater Existing Heating System Air Flow - ceiling fans, through wall grates Existing Structures -fireplace, hearth, ... See #7.
Spray Foam Insulation, Custom Foam Packaging, Floral Applications
...possible to simply raise the surface temperature to a level that would be closer to ideal temperatures. Allow that layer to cure. Then add the desired thickness to achieve your R-factor. Surfaces that are too warm may result in the foam curing too fast. This would also result in a reduced yield because the foam would not have enough time... See #8.
|
Home Guard Entry Door Division
All Home Guard doors feature steel edge construction and are fully insulated in environmentally friendly polyurethane foam and offer a superior R-factor of 15.1 for the ultimate in energy conservation. Home Guard doors have no wood in them which eliminates the opportunity for them to swell, split, twist, ... See #9.
|
|
Low Density Spray Foam Systems, Low Density Spray Foam Insulation, RHH Foam Systems
Manufacturers of low density spray foam insulation systems in two sizes. This spray foam has 25% closed cell with a higher water absorption rate with an r-factor of 5 per inch. See #10.
|
Dyplast Announces Industry-Best K-factor
K-factor, R-factor, polyiso insulation, thermal conductivity, thermal resistance, polyisocyanurate insulation>
See #11.
|
